Concrete Paint

Rustoleum Epoxy Shield garage floor coating is actually a two portion water based epoxy coating program that offers superior protection and durability in just 1 coat.

Rustoleum Epoxy Shield is often a high efficiency, quick to apply garage floor coating. Preparation could be the key to a lasting finish, so it truly is critical that you simply follow all preparation and application directions carefully.

Be conscious that not all concrete surfaces are appropriate for painting. Examine your garage surface for:

• Sealant
• Poorly bonded previous concrete paint
• Moisture in the concrete
• Loose or poorly cured concrete
• Concrete dust

In the event you suspect your floor has any of these conditions, test the surfaces as directed on the Rustoleum epoxy shield instruction paper.

Apply the epoxy shield when the outside temperature falls between 60° F and 85° F with the garage floor having at least 55° F.

Initially, use rustoleum epoxy shield robust degreaser, or perhaps a solvent like mineral spirits, and use a scrub brush to remove any oil or grease spots on the floor. Scrub the spots thoroughly, and absorb excess cleaner with paper towels or rags. Rinse fully to eliminate all cleaner and contaminants. Repair damage areas with epoxy shield concrete patch and repair and allow it to fully remedy ahead of proceeding.

Subsequent, prepare the whole surface utilizing the concentrated cleaner included inside the kit. Mix the cleaner in concentrated form with water (about two gallons should do it), till all cleaning material has dissolved. Employ a plastic watering can to assist you evenly distribute the solution. Prewet the entire floor using a garden hose then scrub the cleaner remedy over the surface in ten feet by ten feet parcels. Perform the solution into the concrete making use of a stiff bristle brush as each section is completed. Rinse thoroughly with water, continuing to scrub with the brush to force eliminate dirt and contaminants out of the garage floor.

Here is usually a tip: use an affordable foam squeegee to most successfully move dirt and water out, reducing drying time. Rinse the squeegee twice before moving on towards the next section.

Once all sections are completed, rinse and squeegee the whole floor to get rid of any cleaner that may possibly have been trapped on previously cleaned locations. A wet-dry vacuum can also be utilized to remove excess water and contaminants.

Allow the entire concrete surface to dry totally. Wipe your own fingers on the clean, dry floor. Should you see any dust or powder on your fingers, repeat the rinsing and scrubbing till the floor is clean.

Rustoleum Epoxy Shield application process

Now, activate the rustoleum epoxy shield technique by pouring all of portion A into portion B. Stir thoroughly having a mixing stick for no less than 3 minutes. Immediately after stirring, check the temperature charts from the rustoleum epoxy shield directions sheet for the suitable application time. This permits the epoxy shield to totally activate.

When mixed, the product must be use within the time indicated inside the charts. Don’t leave the mixed item in sunshine. Stir the mixture 1 extra time prior to applying. Note that painted garage floors might be slippery when wet. If you would like you’ll be able to add epoxy shield anti-skid additive to the mixed coating to make a slippery resistant surface. If applying a lot more than two kits, don’t mix kits at the very same time – to make sure gloss and color are even, the painting must be applied within the specified time-frame.

Here is really a handy tip: after activating, read the temperature charts to determine when you can start out trimming around the perimeter and on difficult to reach areas.

Photo courtesy of SupremeCrete.

Work with the roller to apply the coating in four ft x 4 ft sections. Once a section is completed, sprinkle the decorative chips more than the wet film. For greatest results, toss the flakes within the air and permit them to fall evenly in a “make it rain” type of move. Continue in this fashion till the whole floor is complete.

Rustoleum Epoxy Shield has a low odor, environmentally friendly coating, and cleanup is quick. Just use soap and water to clean up your hands and tools. The surface must be ready for light foot visitors in approximately 12 to 16 hours. Wait 24 to 48 hours before placing heavy items on the floor and permit the floor to remedy for a week ahead of parking vehicles on top.

Rustoleum Epoxy Shield readily available in precise formulations, for garage and basement floors, and is offered in grey and tan. For industrial grade efficiency, use epoxy shield specialist grade coating.